Infiniti QX4 service since 1996 of release
1. Introduction
2. Maintenance instruction
3. Routine maintenance
4. Engine
5. Cooling and heating systems
6. Power supply systems and managements
7. Start and charge systems
8. Transmission line
9. Brake system
10. Suspension bracket and steering
10.1. Specifications
10.2. Assessment of the general condition of components of a suspension bracket and car steering
10.3. Check of a condition and replacement of spherical support of a forward suspension bracket
10.4. Check of a condition of steering drafts
10.5. Removal and installation of the cross-section lever of a forward suspension bracket
10.6. Adjustment of a pretightness of stupichny bearings of forward wheels
10.7. Removal, check of a condition and installation of screw springs and rack-mount assemblies of a forward suspension bracket
10.8. Removal and installation of stupichny assembly and rotary fist
10.9. Removal, check of a condition and installation of the forward stabilizer of cross-section stability
10.10. Replacement of stupichny bearings
10.11. Check of a condition of shock-absorbers and springs of a back suspension bracket
10.12. Removal and installation of components and assembly of a back suspension bracket
10.13. Removal, check of a condition and installation of levers of a back suspension bracket
10.14. Removal, check of a condition and installation of screw springs of a back suspension bracket
10.15. Removal and installation of shock-absorbers of a back suspension bracket
10.16. Removal and installation of the back stabilizer of cross-section stability
10.17. Removal, check of a condition and installation of a cross-section jet bar of a back suspension bracket
10.18. Pumping of a hydraulic path of a steering drive
10.19. Checks and adjustments of a steering wheel
10.20. Check of effort of resistance to sliding of a lath of the steering mechanism
10.21. Adjustment of a torque of a provorachivaniye of a leading gear wheel of the steering mechanism
10.22. Check of hydraulic pressure of GUR
10.23. Adjustment of effort of a tension of a belt of a drive of the steering pump
10.24. Removal and installation of reduktorny assembly
10.25. Removal and installation of assembly of the steering mechanism
10.26. Removal and installation of the steering pump
10.27. Removal and installation of a steering wheel
10.28. Removal and installation of assembly of the combined podrulevy switches
10.29. Removal and installation of the lock of ignition / blocking of a steering column
10.30. Removal, check of a condition and installation of a steering column
10.31. Corners of installation of forward wheels
11. Body
12. Electric equipment
 








8099f600






10-7-snyatie-proverka-sostoyaniya-i-ustanovka-vintovykh-pruzhin-i.html

10.7. Removal, check of a condition and installation of screw springs and rack-mount assemblies of a forward suspension bracket

Before removal of components check a condition of shock-absorbers and screw springs on the car standing on the earth. Serially press on each of car corners — serviceable shock-absorbers provide corner return at an otpuskaniye for one muscleman a body. For an assessment of a condition of screw springs several times rock the car for a usadka of components, then check height of landing of a body (nominal rates — see an illustration the Assessment of a condition of screw springs) — the given springs are not subject to regenerative repair and should be replaced.


Assessment of a condition of screw springs

Hf — 815 mm

Hr — 855/846 mm (see. Specifications)


Removal

 PERFORMANCE ORDER

  1. To Poddomkratta the car also establish it on props (see an illustration the Scheme of an institution of props for car fixing in the lifted situation). Remove the corresponding forward wheel.
  2. Disconnect from a rack a bar of the stabilizer of cross-section stability.
  3. Prop up I will lower the cross-section lever of a suspension bracket.
  1. Mark the provision of a rack of rather rotary fist, then give fixing nuts and bolts of the bottom support of rack-mount assembly.
  2. Release nuts of fastening of the top support of a rack to a car body — do not turn on a nut of fastening of a rod of the shock-absorber.
  1. Remove rack assembly with a screw spring from the car, transfer it on a workbench and clamp in a vice with soft sponges.
  1. Slightly weaken a nut of a rod of the shock-absorber, then compress a screw spring by means of the special tool and finally unscrew a nut.
  1. The final otdavaniye of a nut of a rod of the shock-absorber is made after compression of a screw spring.
  1. Remove from rack-mount assembly a screw spring.


Check

 PERFORMANCE ORDER

  1. Estimate smoothness of courses of compression and stretching are resistant.
  1. Examine assembly on existence of signs of development of leaks.
  1. Make sure of absence on the piston of cracks, deformations and other mechanical damages.
  2. The faulty rack is subject to replacement.


Installation

 PERFORMANCE ORDER

  1. Plant on rack-mount assembly a screw spring (a flat end face up) and make sure of hit of the bottom end face its prutka in reciprocal deepening in a saddle.
  1. Track, that the top saddle of a spring appeared is developed by U-shaped cut to DP of the car and on one line with points of fastening are resistant to a rotary fist.
  1. Further installation is made as it should be, the return to an order of dismantle of components. Track, that all fixture was tightened with demanded effort.


«on page back
10.6. Adjustment of a pretightness of stupichny bearings of forward wheels
on the following page»
10.8. Removal and installation of stupichny assembly and rotary fist