Infiniti QX4 service since 1996 of release
1. Introduction
2. Maintenance instruction
2.1. Access, protection
2.2. Elements of systems of safety
2.3. Car equipment, arrangement of devices and governing bodies
2.3.1. The dashboard - the general information
2.3.2. Combination of devices
2.3.3. Display of a conclusion of compass readings and sensor of temperature of external air
2.3.4. Governing bodies and salon equipment
2.4. Comfort
2.5. Operation receptions
2.6. A mode of operation in emergencies
3. Routine maintenance
4. Engine
5. Cooling and heating systems
6. Power supply systems and managements
7. Start and charge systems
8. Transmission line
9. Brake system
10. Suspension bracket and steering
11. Body
12. Electric equipment
 












8099f600

2-3-4-organy-upravleniya-i-oborudovanie-salona.html

2.3.4. Governing bodies and salon equipment

Left podrulevy the switch serves for switching of modes of functioning of running lighting and alarm devices, and also for activation of indexes of turns.


Activation of running fires and inclusion of a passing beam of headlights

For activation of running fires turn the face handle of the lever of the podrulevy switch in the first fixed situation.

Thus there will be an inclusion of lobbies and back marker lights, lamps of illumination of registration plate and dashboard illumination. For transfer of headlights to a mode of a passing beam it is necessary to turn the face handle of the main switch in the second fixed situation — all other running fires will continue to function as before.

For the purpose of economy of an expense of the electric power switching off of ignition function of automatic shutdown of external lighting devices (including fog lights) on the expiration of 45 seconds after ignition switching off is provided. To similar result leads also opening of any of forward doors of the car. If the face handle of the podrulevy switch is left any of working provisions or , it is enough to make ignition inclusion for activation of lighting devices.

Repeated activation of external lighting devices by means of the podrulevy switch after their automatic shutdown leads to blocking of function of automatic shutdown — in order to avoid risk of a podsadka of the storage battery, do not forget to return the face handle of the switch in the situation OFF, leaving the car for long term. Also avoid long use of external lighting at the idle engine.


Running fires of day time of day (only Canadian models)

On equipped with system of running fires of day time of day (DRL) models of a headlight join in a luminescence mode with small intensity at the started engine and the removed parking brake. The face handle of the left podrulevy switch thus can be both in situation, and in the situation OFF. For transfer of headlights to a mode of a passing beam it is necessary to turn the handle in situation. For deactivation of DRL it is necessary to switch off ignition, having turned a key in the situation OFF.


Activation of a driving beam of headlights

There are two ways of activation of a driving beam of headlights: the first means inclusion of a driving beam in the constant mode, the second is used for the alarm system by a driving beam.

For activation of a driving beam in a constant mode it is necessary to wring out the lever of the left podrulevy switch from itself, having transferred it to the fixed situation. In this mode inclusion of a driving beam is obviously possible only at included running fires (see above).

For short-term activation of a driving beam for the purpose of the alarm system it is enough to delay the switch lever on itself — the otpuskaniye of the lever will lead to shutdown of a driving beam. Short-term inclusion of a driving beam is made irrespective of, in what situation there is a rotary face handle of the main switch see above).


Activation of fog lights

The rotary ring switch of management is located with functioning of fog lights on the handle of the lever of the left combined podrulevy switch and can be established in one or the other fixed provisions: OFF (Vykl) or.


Activation of fog lights is represented possible only at the included passing beam.


Inclusion of indexes of turns

Inclusion of indexes is made by means of the lever of the left combined podrulevy switch. The lever is transferred up or down, to dependences of the chosen direction of a change of course.

At transfer of the lever to extreme top / bottom situation (before click) the corresponding indexes of turns will continue to function until the steering wheel will not be returned in rectilinear situation, or the lever will not be returned in the central situation compulsorily.

Short-term inclusion of indexes, for example, for example, at intention to replace a movement ryadnost, is made by easy procrastination of the lever up or down, respectively.


Right combined podrulevy the switch

Right podrulevy the switch is intended for management of functioning of cleaners and washers of wind and back glasses.


Management of functioning of cleaners and windscreen washers

Inclusion of cleaners / washers of a windscreen can be made only at the included ignition (situation ON and ASS).

The choice of modes of functioning of screen wipers is made by moving of the lever of the switch down / up. Parameters of an interval mode of functioning of screen wipers (in a range of 4 — 12 seconds) can be chosen by means of the rotary face handle on the lever end (see in the same place).


Screen wipers should be included in frosty weather only after the windscreen will be heated-up!

For giving on glass of washing liquid it is necessary to pull the switch lever on itself — screen wipers also should join on some cycles.

It is not necessary to include washers more than for 30 seconds. It is not necessary to make attempts of inclusion of supply of liquid at the empty tank.


Management of functioning of a cleaner and washer of back glass

Activation of a cleaner / washer of back glass can be made only at the included ignition (situation ON and ASS).

For screen wiper inclusion in an interval mode of functioning turn the ring handle on the lever of the podrulevy switch on one division clockwise, having transferred it from neutral (OFF) of situation to situation. Handle turn on one division leads to inclusion of a low-high-speed mode of functioning of a screen wiper.


Activation of a back screen wiper can be made only at the locked back glass, and closing of glass should be made at the switched-off screen wiper. Opening of back glass at a working screen wiper also is not obviously possible.


The screen wiper should be included in frosty weather only after back glass will be heated-up!

For giving on glass of washing liquid it is necessary to turn the handle against the stop in any direction — the screen wiper also should join on some cycles.

It is not necessary to include supply of washing liquid more than for 30 seconds! It is not necessary to make attempts of inclusion of supply of liquid at the empty tank!


Regulator of intensity of illumination of the dashboard

The regulator of intensity of illumination is built in in the car dashboard more to the left of a steering column (see an illustration the Scheme of an arrangement of governing bodies on the car dashboard). Demanded intensity of illumination of the panel is made by potentiometer rotation.


The regulator starts to function only at included running fires (see above).


Switch of the alarm light system

Turning on of the alarm system is made by an otzhimaniye of the push-button switch which has been built in in the central part of the dashboard of the car (to the right of a steering wheel, under the deflector of the central air line of ventilation / heating of salon — see an illustration the Scheme of an arrangement of governing bodies on the car dashboard) and usually equipped with a control lamp with the pictogram representing two entered one in another of triangles.

Turning on of the alarm system can be made in any position of the ignition key and leads to simultaneous operation of all four indexes of turns (and their control lamps on an instrument guard of the car) the Alarm system is intended for the prevention of other participants of traffic of the compelled stop of the car and is used also in other dangerous situations provided by traffic regulations.

At the switched-on alarm system indexes of turns will not function!


Switch of electroheating of back glass / external rear-view mirrors

The push-button switch of heating back glasses / rear-view mirrors is located directly under the switch of the alarm system and is equipped with the built-in control lamp (see an illustration the Scheme of an arrangement of governing bodies on the car dashboard).

Inclusion of electroheating allows to remove from surfaces of back glass / door rear-view mirrors of condensate, hoarfrost, and even thin fly. At inclusion of an electroheater the light indicator lights up built in the switch button. Shutdown of heating is made by repeated pressing the button.

The threadlike grid of a heating element of a heater is pasted on an internal surface of back glass and demands care in the address — try not to damage a grid when wiping glass. Wiping should be made only along heater threads.

Functioning of a heater is interfaced to the raised level of power consumption therefore, in order to avoid a podsadka of the storage battery, the timer making automatic shutdown of system after 15 minutes of its continuous work is switched on in a chain of management of the device.

Do not forget to check before a start of motion quality of the review through back glass of the car.


Horn switch

As the button of a horn the decorative cover of a stupichny part of the steering wheel / module of a safety cushion acts. For activation of a sound signal it is necessary to press the central part of the button.


Switches of management of heating of forward seats

Forward seats of the car are equipped with the built-in heaters. Switches of management are located heating of seats in the lower part of the central section of the dashboard (see an illustration the Scheme of an arrangement of governing bodies on the car dashboard) and equipped with the built-in control lamps. Activation of heating elements (TAN) of driver's and passenger seats can be made independently.

Start the engine — inclusion of heating of seats at the muffled engine leads to the fast category of the storage battery.

Having pressed the relevant party of the keyboard switch, choose a demanded mode of intensity of heating — on a key the corresponding indicator should be highlighted. Management of TAN'S functioning is carried out automatically by means of the thermostat. Do not forget to switch off heating before leaving the car.


Do not cover a seat with heatinsulating materials, such as blankets, padded stools or dense covers!
Do not put on seats firm or sharp subjects, try not to allow risk of damage of an upholstery and the heating element located under it!
Any liquid spilled on a seat immediately collect dry rags!
Do not apply to cleaning of an upholstery of seats any solvents — use soft детергентами!
In case of violation of serviceability of functioning of heating of seats address for the help in car-care center!


Switch of management of functioning of the electric drive of rear-view mirrors

Assembly of management by functioning of the electric drive of external rear-view mirrors is built in in the car dashboard, to the left of a steering column (see an illustration the Scheme of an arrangement of governing bodies on the car dashboard).

Assemblies of management of two types are used: And and Century.

In type A assembly the choice of a mirror subject to adjustment is made by means of the push-button switch.

L — the Left mirror
R — the Right mirror


 PERFORMANCE ORDER

  1. Include ignition (the provision ON or ASS of a key).
  2. In pressing the relevant party of the push-button switch make a choice of a mirror subject to adjustment.
  3. By means of the dzhoystikovy switch make correction of provision of the chosen mirror.
  4. After completion of adjustment repeatedly press the button for a drive conclusion in neutral situation — it is necessary in order that by casual pressing the button not to break adjustment.

In type assembly In a choice of a mirror it is carried out by a povorachivaniye of the handle of the unique dzhoystikovy switch in the relevant party. Further actions are similar described above for type A system — do not forget to return the handle to neutral situation.

L — the Left mirror
R — the Right mirror


Switches of management of functioning of the electric drive of window regulators

The electric drive of window regulators remains active within 45 more seconds after ignition switching off, opening within the stipulated term of any of forward doors of the car leads to shutdown of giving of a food on a drive.


Main control panel functioning of the electric drive of window regulators

1 — the Switch of a window regulator of the left back door
2 — the Switch of a window regulator of a driver's door
3 — to Press for glass lowering
4 — to Pull for a glass podnimaniye

5 — the Button of activation of the uniform lock
6 — the Switch of a window regulator of the right back door
7 — the Switch of a window regulator of the right forward door
8 — the Button of blocking of individual switches of passenger doors

The electric drive of window regulators functions only at the included ignition. The main control panel functioning of the electric drive of window regulators of marks of doors it is located on an armrest of a driver's door (see an illustration the Main control panel functioning of the electric drive of window regulators).

For a lowering / podnimaniye of glass use the corresponding individual switch (address to an illustration 14.15). Possibility of management by window regulators of all doors from a driver's place (see an illustration the Main control panel functioning of the electric drive of window regulators) is provided.

The button allowing the driver to block regulators of all passenger doors (see an illustration the Main control panel by functioning of the electric drive of window regulators) is also provided. For shutdown of blocking press the blokirator button repeatedly. For a lowering / podnimaniye of glass press / delay a key of the corresponding switch and hold her in this situation.

Possibility of machine translation of glass of a driver's door in extreme bottom situation is provided — rather quickly strongly to press the AUTO key of the control panel of a driver's door (at an otpuskaniye of slightly pressed key lowering of glass will stop). To suspend process of automatic lowering of glass delay a key up.


Management of functioning of a drive of the top hatch

The electric drive of the top hatch remains active within 45 more seconds after ignition switching off, opening within the stipulated term of any of forward doors of the car leads to shutdown of giving of a food on a drive.


The electric drive of the top hatch functions only at the included ignition. The cover of the hatch can move back, parallel to a roof surface, bend forward with lifting of its back edge.


The control panel is located functioning of the electric drive of the top hatch on the ceiling console of the car.

To shift a cover of the hatch wring out a rychazhok of the left switch of the panel back (towards the pictogram) and hold him in this situation. Closing of the hatch is made by an otzhimaniye a rychazhka to the opposite side ().

For transfer of a cover of the hatch to inclined situation at first completely close it, then wring out and hold pressed the key of the switch marked with the pictogram. Lowering of a cover is made by an otzhimaniye of the opposite side of a key.

In addition top hatch is equipped with a sun-protection shtorka. When moving a cover of the hatch the shtorka is cleaned automatically. Closing of a shtorka is made manually.

Watch, that passengers were not put out in the hatch during car movement. Before opening of the hatch clear a cover of moisture, snow, a dust and other extraneous deposits. Do not put on a cover of the hatch and a surface of a roof of the car near the hatch any heavy subjects!
At failure of the electric drive of a cover of the hatch the car should be driven away on car repair shop for performance of the corresponding regenerative repair.


Switch of the uniform lock

See. Access, protection.


Switches of management of functioning of the electric drive of adjustment of provision of forward seats

See. Elements of systems of safety.


Switch of modes of functioning of a transfer case (4WD)

See. Operation receptions.


Switches of management of functioning темпостата

See. Instructions for use control system of the speed (tempostaty).


Switch of an all-wheel drive mode

See. Operation receptions.


Ignition switch

See. Removal and installation of the lock of ignition/blocking of a steering column.


Hours

Digital watch is built in in a regular audiosystem (see. Comfort). Indications of hours are displayed the display only at the included ignition (a key in the situation ON or ASS). After shutdown of an onboard food of the indication of hours are dumped and should be established anew.


Time installation

Installation of indications of the current hour is made by means of the button (N), minute — by means of the button (M).

By means of the CLOCK button on the control panel of an audiosystem the choice of a mode of functioning of the display (hours / radio tape recorder) is made.

In the CLOCK mode of the indication of the current time have an absolute priority — parameters of functioning of an audiosystem will be displayed only quickly at change of modes.

After implementation of control of the current time the display is transferred to the CLOCK mode automatically.


Sockets of onboard power supply


Two options of execution of the socket of onboard power supply

The socket of an onboard food is intended for connection of auxiliary electric equipment. The key should be turned in the situation ON or ASS.

On the car two sockets of a food — one in a back face wall of the central console, the second — in the right back corner of a luggage compartment, near a cover of a ware box are provided. Both sockets are equipped with a protective cover which should be held at not connected equipment closed (see an illustration Two options of execution of the socket of onboard power supply).


Precautionary measures

  • Tension of the onboard power supply makes 12 volts — do not connect to the socket consumers in capacity over 120 W (10 And)!
  • The socket is not intended for turning on of the lighter at it!
  • In order to avoid a discharge of the storage battery when using auxiliary electric equipment do not suppress the engine!
  • Try not to use auxiliary electric equipment at the included headlights, the air conditioner, or heating of back glass!
  • Before extraction from the socket of a plug of electroconducting without fail switch off a food of the used auxiliary electric equipment!
  • The plug of electroconducting of the connected equipment should enter into the socket against the stop, providing reliable electric contact!
  • In a usage time of a surface of the socket and a plug of electroconducting connected to it can be warmed up to high temperature and remain warmed up during even some time after shutdown!


Lighter and ashtrays


Location and rules of use of the lighter and ashtrays

Originators of the real Management do not recommend to use a lighter nest as a nest of selection of an onboard food (see above).

The lighter is located in the lower part of the central section of the dashboard (see an illustration the Scheme of an arrangement of governing bodies on the car dashboard) and functions only at the included ignition (situation ON and ASS). For turning on of the lighter drown before click its button (see the illustration Location and rules of use of the lighter and ashtrays). After heat of a spiral the button automatically with click will return to a starting position.

In order to avoid a lighter exit out of operation, do not hold its button during spiral heating!

The forward ashtray is built in in a forward part of assembly of the central console directly under the lighter, back is located in a back part of the console, the nest of selection of an onboard food (see the illustration Location and rules of use of the lighter and ashtrays) is more right.


Coin box

The coin box is built in in the left part of the dashboard (see an illustration the Scheme of an arrangement of governing bodies on the car dashboard) and not intended for storage of valuable subjects.


Case for storage of sunglasses

The case for storage of sunglasses is built in in assembly of the ceiling console and equipped with a latch with the press button.


Do not leave points in a case in the car parked on the open sun — as a result of heating plastic can melt!


Coasters

In the car some coasters both opened, and the closed type are provided.

Two sets of forward coasters are located in the main section of the central console — is more right than the lever of raising of the parking brake (coasters of open type) and is more left than the AT selector lever (a coaster of the closed type).


Back coasters it is equipped on the sliding panel in a back face wall of the console, ashtrays and nests of selection of a food are lower.


Using coasters of the closed type should be made only during car parking!


Ware boxes


Main ware box

The main ware box is built in in the right part of the dashboard, under the module of a passenger face-to-face safety cushion (see an illustration the Scheme of an arrangement of governing bodies on the car dashboard).

Unlocking / locking of a ware box can be made only by means of the main key. For opening of a cover of a box it is necessary to delay on itself the handle of its lock — the zashchelkivaniye of the lock is made automatically when closing cover. Box opening at the included ignition is accompanied by automatic inclusion of its illumination.


Leaky closed cover of a ware box at a road accident can become the reason of a serious travmirovaniye of the passenger sitting on a forward seat even if it will be fastened by a seat belt!


Console ware box


Design of a console ware box

One more ware box, the smaller size, built in in a back part of the central console, consists of two offices, is equipped with a folding cover, intended for storage of route charts and equipped with a folding table-top and a kartoderzhatel (see an illustration the Design of a console ware box).


Ware boxes of a luggage compartment


Ensuring access order in offices of a lateral ware box of a luggage compartment


Equipped in a floor of a luggage compartment the ware box is equipped with a cover leaning back on loops

 

The ware boxes equipped in a luggage compartment are not intended for storage of valuable subjects.

In a luggage compartment two ware boxes are equipped. One of boxes is located in the right lateral wall and equipped with the demountable cover fixed by two rotary clamps, in a floor of box space one more small office with the cover equipped with a press clamp (see an illustration an ensuring access Order in offices of a lateral ware box of a luggage compartment) is located. When closing covers track reliability of fastening of covers clamps.

The second box is located in a niche in a floor of a luggage compartment, under a carpet and is equipped with a cover leaning back on loops (see the illustration Equipped in a floor of a luggage compartment the ware box is equipped with a cover leaning back on loops).


Equipment of a luggage compartment


Fittings for fastening of cargo placed in a luggage compartment

For reliable fixing of transported cargo in a luggage compartment of the car some hooks are provided.

A.

B.

Four hooks are fixed on lateral stacks of office (under two from each party — A), two from above over lateral window leaves and four more (B) on a floor.

Hooks are intended for fastening to them cables fixing cargo and extensions and no more than 10 kgfs everyone are calculated on loading.


Scheme of fastening of a luggage network

Four back hooks can be used for fastening to them a luggage network.

Hooks And and In are not intended for fastening of a network.


The mass of cargo fixed by a network should not exceed 13.6 kg!
Cargo in a luggage compartment should not take place above level of the top cut of backs of seats!


Top shtorka of a luggage compartment

Shtorka is intended for concealment of the subjects which were in a luggage compartment from an extraneous look. The taking-up drum of a shtorka is fixed behind a back of a back seat. Having pulled, unwind a shtorka and fix its corners on lateral hooks.


Do not put from above on a shtorka any subjects which can easily break during sharp braking and put a trauma to passengers sitting in salon!
Do not leave the shtorka removed from holders in a luggage compartment!
When unwinding a shtorka track reliability of fixing of its corners on hooks of a luggage compartment!


Top luggage carrier

Location of cross-section laths of a frame of the top luggage carrier can change in the longitudinal direction of rather diametrical plane (DP) of the car.

Lay luggage a luggage carrier between laths (And) a luggage carrier, adjust position of the last, then attach to them luggage by means of a cord — specially for this purpose on lateral laths of a frame adjustable loops are provided.

Try to distribute cargo transported on a roof evenly. The total weight of luggage should not exceed 45 kg. Also track, that the gross weight of a vehicle (GVWR) and axial loadings (GAWR) did not exceed admissible values according to Specifications (see information provided on a certified label on a back rack of a driver's door — see. Introduction, also see. Head Maintenance instruction).


Sun-protection peaks


Options of application of sun-protection peaks

Two harmonious sun-protection peaks are located over the upper edge of the wind flew down the car and serve for protection of eyes of the driver and the forward passenger against hit of direct sunshine. If beams fall in front, the peak should be lowered simply, having turned it on axial loops down (see an illustration Options of application of sun-protection peaks). For protection against light falling sideways, the peak should be liberated from an internal loop and to develop towards a door. In case of need at the turned peak for protection against frontally directed beams the additional guard can be lowered.


Internal rear-view mirror

The design of a drive of an internal rear-view mirror provided two regular situation: one is intended for movement during daylight hours, another — in dark. In the second situation reflecting ability of a mirror decreases that promotes weakening of blinding action of headlights moving behind vehicles. Mirror transfer from day situation in night also is back made by means of special, built in in assembly from below a rychazhka. Pressing a rychazhok forward or back, choose the demanded provision of a mirror.


Harmonious external rear-view mirrors

The design the basis of door rear-view mirrors allows to put them, densely pressing to glass of doors.


Toilet pocket mirror

The toilet pocket mirror is established in a sun-protection peak, protected by a cover and equipped with illumination (see below).


Devices of internal lighting


Ceiling lamps

On the panel of a ceiling upholstery two ceiling lamps settle down: central and illuminations of a luggage compartment.

Switches of both lamps have Polzunkovye on three fixed situation. In situation activation of lamps occurs each time when opening any of car doors.

At performance listed below conditions lamps will continue to function within 30 seconds:

  • One of forward doors of the car leans from the DU panel of the multipurpose controler or by means of a key if all doors of the car were in the locked situation;
  • When unblocking a driver's door at the ignition key taken from the lock;
  • When opening and the subsequent closing of a driver's door while other doors of the car remain closed;
  • At key extraction from the ignition lock behind closed doors the car.

Shutdown of ceiling lamps at the activated 30-second timer occurs in the following situations:

  • When locking a driver's door by any of regular ways;
  • At ignition inclusion.

Positions of ON and OFF switches correspond to constantly included and constantly switched off conditions of lamps respectively.

With a view of economy of expenses of the electric power function of automatic shutdown of all internal lamps which switches are transferred to the situation ON on the expiration of 10 minutes after ignition switching off is provided. For repeated activation of lamps it is necessary to turn a key in the situation ON.

After performance described above procedure shutdown of lamps on the 10-minute timer will occur in the following cases:

  • Opening or closing of any of doors;
  • Unlocking or locking of a driver's door;
  • Key insertion in the lock of ignition or its extraction from the lock.


Personal lamps

Two personal lamps are built in in the panel of the ceiling console of the car. Lamps are equipped with push-button switches and submit to the general scheme of functioning of the 10-minute timer of internal lighting devices (see above).


Illumination of a toilet pocket mirror

The toilet pocket mirror built in in a sun-protection peak is equipped with the individual illumination which activation occurs when opening a protective cover of a pocket mirror.

On pocket mirror illumination the scheme of functioning of the 10-minute timer of internal lighting devices (see above) also extends.


The built-in universal device of remote radio management of HomeLink®


General information

The built-in universal device of remote radio management (Transceiver) of HomeLink® allows to unite conveniently functions to three separate devices of radio management and allows to operate functioning of the majority of radio frequencies of actuation mechanisms working in a range, such as a drive of a garage door, activators of door locks and security systems.

A food of the transceiver is carried out from the onboard storage battery that excludes need for performance of periodic replacement of an element of a food, memory is organized by ROM principle that means lack of need of repeated data input after battery shutdown.

After introduction in the transceiver of a program code the original control panel (charm) should be kept on a case of emergence of need of repeated programming (for example, in case of acquisition of the new car). At car sale the program code of the transceiver should be removed from memory of the device for safety. For more details see below.

The built-in Universal HomeLink® Transceiver is not intended for use with actuation mechanisms of opening of garage doors in which function emergency останова reverse inclusions is not realized. These requirements were standardized for actuation mechanisms of release since April 1, 1982!
At input of a program code of a door of garage can spontaneously start to open or be closed — track, that in a doorway there were no people or pets!
Programming of the transceiver should be made at the muffled engine!


Programming of the Universal HomeLink® Transceiver

 PERFORMANCE ORDER

  1. At the switched-off ignition (a key in the situation OFF) press and hold two external buttons of the control panel of the transceiver and hold them pressed until the light indicator (about 20 seconds) will start to blink — during performance of this procedure memory of the device should be cleared of the operating factory code entered into it by default.

At input in memory of the transceiver of additional data need for performance of this procedure is absent.

  1. Bring the working end of the control panel brought in memory of system of the equipment, to the transceiver on distance about 50 — 125 mm, constantly keeping an eye on the light indicator.
  2. Two hands at the same time press the button of a control panel and the chosen button transceiver control panels — hold buttons pressed until finish procedure of the following item.

For some actuation mechanisms of a drive of garage doors performance of the procedures given in subsection «Transceiver programming for conditions of the Canadian market» (see below) can be demanded.

  1. The control lamp of the transceiver should start to blink, at first slowly, then quickly. When frequency of gleams of a lamp considerably will increase, buttons on both devices can be released.

Input of a program code is made for the remained two buttons of the transceiver in a similar manner with lowering of procedure of removal of a factory code.


Programming of the Universal HomeLink® Transceiver for conditions of the Canadian market

According to the rules accepted till 1992, duration of continuous radiation of transmitters should not exceed 2 seconds. In such conditions at input of a program code nazhimany buttons of the panel (see item 4 of the previous subsection) should be made cycles duration for 2 seconds everyone until frequency of gleams of the light indicator will not reach demanded intensity.

At input of a code of management by the activator of a drive of a garage door, etc. devices it is recommended to disconnect a drive for the period of turning on of the panel, in order to avoid damage of its components.


Ruled uses of the Universal HomeLink® Transceiver

After input of the corresponding program code the Universal Transceiver can be used for management of the corresponding actuation mechanism (for example, operating functioning of a drive of a garage door). For activation of the device it is rather simple to press the corresponding button on transceiver control panels, - during transfer of an operating signal should work the light indicator.


Diagnostics of errors of input of a program code

If it is not possible to enter quickly enough into memory of the transceiver of information from the manual transmitter, it is necessary to operate as follows.

 PERFORMANCE ORDER

  1. Make replacement of an element of a food of the transmitter.
  2. Track correctness of orientation of the podnosimy transmitter to the transceiver (the party with a batareyny compartment should be outside).
  3. Try to hold at the same time pressed buttons on both devices rather reliably.
  4. Track, that during information input the transmitter was on removal from the transceiver no more than 125 mm. If within 15 seconds frequency of gleams of the light indicator does not increase, confirming success of input of a program code, try to repeat procedure, having a little changed position of the transmitter concerning the transceiver — constantly keep an eye on the indicator.

If to enter a code it is not possible under no circumstances, address for consultations on firm car repair shop Infiniti.


Removal of a program code from memory of the Universal HomeLink® Transceiver

Possibility of cleaning of the data entered for the separate button of the transceiver by a design of the device is not provided. For removal of all entered information it is necessary to hold within about 20 seconds pressed at the same time two lateral buttons on the transceiver control panel. Buttons can be released as soon as the light indicator will start to blink.


Input of a dynamic program code

Activators of a drive of garage doors with a dynamic code started to be issued since 1996 and can be identified by one of the next ways:

A.Svyazhites with representatives of the company manufacturer of the device.

V.Priznakom of use of a dynamic code is that fact that, despite a successful conclusion of procedure of input of a program code from the panel usual way, activation of the corresponding device from the transceiver is not represented possible.

S.Uderzhivayte the corresponding button of the transceiver pressed — if the actuation mechanism is equipped with a dynamic code, the light indicator of the transceiver at first will often blink, then, later pair of seconds will pass to a mode of a continuous luminescence.

For management from the transceiver the device with a dynamic code, input of a program code should be made as follows.

 PERFORMANCE ORDER

  1. Find on the block of the driving electromotor of the actuation mechanism the fine tuning button — exact location and color of the button can differ depending on device brand — in case of need address for the help to representatives of the company manufacturer.
  2. Press the button — the adjusting lamp can light up.

Procedure of the following item should be complete within 30 seconds from the moment of button pressing.

  1. Firmly squeeze out, then release the programmed button of the transceiver. For completion of process of control once again press the transceiver button (the design of some actuation mechanisms demands a triple nazhimaniye of the programmed button).

Now the receiver of the actuation mechanism should start to perceive a signal given out by the transceiver. Further, in case of need, programming of the remained two buttons of the device can be made.


Reprogramming of separately taken button of the Universal HomeLink® Transceiver

For change of a program code of separately taken button of the transceiver act as follows.

 PERFORMANCE ORDER

  1. Press the button of the control panel of the transceiver subject to reprogramming and do not lower it before procedure completion (see item 4).
  2. When about 20 seconds later the light indicator of the transceiver will start to blink slowly, bring to the control panel the manual transmitter of the new device, the chosen button will be intended for management which, the transmitter should be brought to a transceiver surface on distance of 50 — 125 mm.
  3. Press and hold pressed the transmitter button.
  4. The control lamp of the transceiver should start to blink at first slowly, then quickly — when frequency of gleams of a lamp considerably will increase, buttons on both devices can be released.

Now the reprogrammed button can be used for management of the new device.


Operations procedure in case of car stealing

When stealing the car it is necessary to reprogram actuation mechanisms of all devices put in action from the transceiver which have not been equipped with function of a dynamic code — in case of need consult at representatives of the relevant firms manufacturers.

At return of the stolen car it is necessary to make reprogramming of all buttons of the built-in transceiver.

According to the rules FCC to which the design of the Built-in Universal HomeLink® Transceiver answers, the device (1) should not develop unhealthy radiation and (2) should perceive any induced signals, including what can lead to undesirable operations.


The design of the Universal HomeLink® Transmitter meets the requirements of the rules FCC and DOC/MDC. Attempts of updating of the transceiver are fraught with cancellation of rights of use by the equipment!

DOC: ISTC 1763К1313

FCC I. D.: CB2V67690.


Onboard communicator of Infiniti


General information


Control panel of an onboard communicator of Infiniti

1 — the Light indicator
2 — the Light indicator of a repeated call
3 — the Light indicator of stay out of an area of coverage of a telecommunication network
4 — the Light indicator

5 — the Button of giving of a distress signal of "Mayday"
6 — the Microphone
7 — the Button of inclusion of information mode
8 — Personal lamps

Basic purpose of an onboard communicator of Infiniti is increase of level of safety of the owner of a vehicle at the expense of granting convenient options of a call of the majority of rescue services. The range of services provided by services is defined on a contractual basis.

The communicator provides possibility of using with such telecommunication systems, as System of Global Positioning (GPS), mobile telecommunication and the Communication Center of Fast Reaction of Infiniti.

The control panel of a communicator is located on the ceiling console of the car (see an illustration the Control panel of an onboard communicator of Infiniti). Two buttons deduced on the control panel allow to submit in case of need a distress signal and to activate a data exchange mode with the Communication Center of Fast Reaction of Infiniti.

Besides, the communicator provides automatic transfer to the center of fast reaction of information on operation of safety cushions and/or the anticreeping alarm system, and also allows to make remote activation of the uniform lock and tracking of the stolen car on a signal of the built-in radio beacon.

In order to avoid dispersion of attention it is not necessary to use a communicator during car movement!
For maintaining telephone negotiations during movement the Hands-Free function is provided — keep the mobile phone under in the special holder. Remember that all attention of the driver should be concentrated to management of a vehicle and tracking of a road situation!
If in the course of negotiations there is a need for conducting any records, it is necessary to park in a safe place!


Some features of the organization of functioning of a communicator

  • Giving of a distress signal and inclusion of a mode of data exchange can be carried out only at the included ignition (a key in the situation ON), or not less than 3 minutes later after its switching off.
  • The delay between pressing the button of a fast call or and the answer of the operator of the Communication Center of Fast Reaction makes about 25 seconds during which the communicator should establish connection and hand over coded information on the car.

In case of strong loading of communication lines time of a delay can increase.

  • The voice communication with Communication the Center is provided at the expense of the communicator of a microphone built in the control panel (see an illustration the Control panel of an onboard communicator of Infiniti) and a loudspeaker of the right forward door. Volume control of sounding can be made by means of the switch of the control panel located on a steering wheel by functioning of the mobile phone (see below).
  • All located on the communicator dashboard light indicators , are intended for control for system functioning (for more details see below). At ignition inclusion indicators are activated for 30 seconds during which the system of self-diagnostics carries out poll of a condition of the corresponding components. If any violations during check it is not found, lamps after the stipulated term should go out.

Performance of cyclic switching of ignition of ON-OFF-ON during 3-minute term does not lead to repeated poll of a condition of system as the last will still remain active.

  • Refusal of switching off of indicators and during 30-second term from the moment of ignition inclusion, or their simultaneous operation during any other time at the included ignition testifies to violation of serviceability of functioning of a communicator — address for consultations on firm car repair shop Infiniti.

Violations not necessarily can lead to refusal of functioning of a communicator.

  • At installation of communication with the Communication Center of Fast Reaction of Infiniti the communicator transfers data on the car on which it is established and about locations of this car.


The list of the functions supported by a communicator of Infiniti


Giving of a distress signal of "Mayday"

At hit in an emergency situation press the button on communicator control panels (see the first point in the previous subsection) — the light indicator built in the button should помигать, then pass to a mode of a constant luminescence, confirming activation of a call of the Communication Center of Fast Reaction of Infiniti. As soon as communication with the center will be established, the communicator automatically will begin transfer of the standard information package including data and a vehicle, its site and type of a call (Mayday). On termination of transfer of a standard package the channel of a voice communication with the operator of the center who is in case of need obliged to provide an immediate call on a scene of the relevant regional rescue service is activated.

If for any reasons the voice communication with the center cannot be established, the operator is also obliged to notify on the accepted call a regional rescue service with the indication of an exact site of suffering disaster of a vehicle. If at an exchange of voice data with the center it will not be transferred to information on an emergency situation, the operator will request from causing in advance stipulated password. Transfer of the false password will be considered as action under the threat of violence and the corresponding rescue team will be immediately directed on a scene. Having finished negotiations, the operator will continue to trace a situation before help arrival.


Activation of a mode of exchange of information

At engine failures and in cases of other breakages in a way when the reason of a non-staff situation cannot be eliminated with own forces it is necessary to press the button of activation of a mode of data exchange on the communicator control panel (see the first point in the previous subsection) — the light indicator built in the button should помигать, then pass to a mode of a constant luminescence, confirming activation of a call of the Communication Center of Fast Reaction of Infiniti. As soon as communication with the center will be established, the communicator automatically will begin transfer of the standard information package including data and a vehicle, its site and type of a call (Information). On termination of transfer of a standard package the channel of a voice communication with the operator of the center who in case of need will provide a call on a scene of the relevant repair service is activated. This mode can be used also for obtaining more detailed information on usings an onboard communicator of Infiniti.


Information transfer about operation of safety cushions

The fact of operation of safety cushions is regarded as a sign of hit of a vehicle in a severe accident. In a similar situation the onboard communicator makes an automatic call of the center of fast reaction of Infiniti with transfer of a standard Mayday package (see above). Having accepted a package, the operator of the center on duty will try to establish a voice connection with crew of the had an accident car and, in the absence of the answer, is obliged to make a call on a scene of the relevant regional rescue service and to remain on communication till help arrival.


Remote activation of the uniform lock

If keys from the car were casually forgotten in car salon, the owner can contact by phone the operator of the Communication Center of Fast Reaction of Infiniti (number should be specified in the communicator passport — it will be reasonable to bring it also in a notebook or memory of the mobile phone) and, having called the password, to request the instruction on remote activation of door locks.


Function of tracking of the car in case of its stealing

Under certain conditions the Communication Center of Fast Reaction is capable to make tracking of the stolen vehicle equipped with an onboard communicator of Infiniti. On phone call correctly called the password of the authorized owner (number should be specified in the communicator passport — it will be reasonable to bring it also in a notebook or memory of the mobile phone) the operator of the Center of Fast Reaction is obliged to inform on the stealing fact regional police / militian service and to make attempt of determination of location of the stolen vehicle (the last is obviously possible only in case will turn the ignition key in the lock in the situation ON). If attempt of determination of location passed successfully, the operator has an opportunity the hidden listening of salon of the car — the relevant information will be transferred also to police / police authorities conducting investigation.


Information transfer about operation of the anticreeping alarm system

At operation of the anticreeping alarm system and functioning it continuously in a current more than 7 seconds the onboard communicator carries out an automatic call of the Communication Center of Fast Reaction of Infiniti with transfer of a standard information package.

The call is made at any position of the lock of ignition. Having estimated a situation, the operator of the Center on duty is obliged to notify the authorized owner of a vehicle on alarm system operation. If the owner is in the car, from it the password will be requested. In case of need, if the ignition key will turn in the situation ON, the operator has an opportunity the hidden listening of salon.


General instructions for use onboard communicator of Infiniti


Automatic repetition call / dumping in a readiness mode

In unsuccessful attempt of installation of communication with the Center of Fast Reaction of Infiniti (for example, in case of line employment), the communicator will automatically make repeated calls during the certain term defined mainly by provider of services of mobile communication, but a two-hour range not exceeding borders. On termination of attempts of installation of communication with the center (successful or unsuccessful), system automatically comes back to a readiness mode — in case of need a cycle the call can be activated repeatedly by a way of pressing of the corresponding button on the communicator control panel. The mode of repetition is automatically activated also in case of break for any reason of the current communication session with the Center. The unique sign of regular end of a session is transfer of the corresponding coded signal — the light indicator of a call on the control panel of the device and should go out. All transferred in communication session time information registers.

Sometimes, at weak level of a signal the Communication Center is not able to finish data transmission, - in case of need renew a session by pressing of the corresponding button control panels.

In case of global natural cataclysms (for example, at earthquake) all communication lines with the Communication Center can appear are overloaded — in similar situations of attempt of renewal of the broken communication by a communicator are not made.


Priority of calls of the Communication Center

If during negotiating by the mobile phone the call of any of regular calls of the Communication Center (by "Mayday", «Information» is made, or any of automatic calls, - see above), telephone conversation will be interrupted.


Roaming

If the provider of telecommunication services chosen by you does not provide roumingovy services, communication session installation with the Communication Center of Fast Reaction of Infiniti from remote areas can appear problematic.


Data transmission

By transfer of any information to the Center of Fast Reaction of Infiniti all entering data are sorted and as a call, to location of a defiant vehicle, the direction and speed of its movement at the moment of transfer.


Function of global positioning

For determination of exact location of Infiniti of a vehicle equipped with a communicator the satellite Global System of Positioning (GPS) is used. About 21 000 km rotating in an orbit GPS satellites continuously radiate radio-waves. GPS receiver, analyzing signals given out by several satellites, calculates exact location of a vehicle on which it is established, in three-dimensional system of coordinates (width, a longitude and height above sea level).

Reception of signals of GPS is blocked in places where distribution of radio-waves is complicated. In a similar situation by transfer by a communicator of a standard information package it is used the last accepted data of GPS. If the data transferred in the Center do not meet standard requirements to reliability, the operator will request information on its exact location from the owner of a vehicle.

Accuracy of determination of coordinates of object in the GPS network is influenced by such factors, as an interference of radio-waves, topography of the district and weather conditions.

Refusals and mistakes when positioning can take place at movement in tunnels, near high-rise buildings or dense a lesoposadok, vehicle transportation on a lower deck of the ferry or the bottom platform of a railway car, parking on a covered parking, etc.

Do not establish near the aerial of a receiver of GPS in the car any objects, capable to prevent perception of a radio signal.

Try to hold on the greatest possible removal from communicator aerials such sources of radiation, as radio telephones and radio transmitters. In a winter season regularly clear the wind and back flew down from snow and ice.

Control of functioning of Global System of Positioning carries out the Ministry of Defence of the USA! Told means that signal level sometimes can decrease considerably, and data transmission without the visible reasons to stop.


Contractual requirements for using services of the Communication Center of Fast Reaction of Infiniti

For implementation of communication with the Communication Center Infiniti from the car your mobile phone should be programmed correctly. About ways of installation of contact to representation of communication system always it is possible to consult at firm car repair shop Infiniti.

In due time inform the Communication Center on changes of number of your phone. To contact the relevant service of the Center always it is possible according to number 888-870-9898.

At sale of the car or making decision on the termination of using by services provided by the Center also in due time inform the operator on duty.


Activation of an onboard communicator of Infiniti

Activation of a communicator should be made during the shortest term after the conclusion of the contract.

For communicator input in action press any of two buttons or panels of its management. After communication session installation the operator of the Center of Fast Reaction on duty will make verification of the data brought in the text of your contract with the representative of the Infiniti company, and also will check serviceability of functioning of the system of positioning of GPS established on the car and will issue the short certificate of services provided by system. In summary possibility of a parolirovaniye of access to system will be offered you. During all process of control of a communicator the system will remain in a demonstration mode during which from a control panel can be transmitted any trial signals For receiving high-grade access to the provided Communication Center to services it is necessary to sign the relevant contract and to receive the account.


Other functions

Ignition switching off during a communication session with the Communication Center Infiniti should not lead to data link break if the onboard storage battery only is not discharged. For the purpose of economy of an expense of the electric power to use a communicator it is better at the working engine if only it does not involve danger of poisoning with carbon monoxide or it is impossible for any other reasons.

Engine start during conversation can lead to communication session break — in a similar situation the communicator can make attempt of renewal of transfer as soon as the engine will be started.

Using an audiosystem during carrying out a communication session with the Communication Center is not obviously possible (Auto mute function), except for cases of the hidden tracking of a situation onboard in cases of stealing or violence threat (see above).

At activation of functions of tracking when stealing or information transfers about operation of the anticreeping alarm system when using of optionally connected phone, some signals can be transferred to this phone.

When switching from a voice mode in a data transmission mode at the end of a communication session in loudspeakers peep and hissing can be reproduced. These sounds are not a sign of violation of serviceability of functioning of system — their reason is transfer by the modem through which connection, office information is carried out.

At refusal for any reason of the onboard storage battery during a communication session with the Communication Center, the communicator after restoration of giving of a food will make attempt of automatic repetition of the last call.


Interpretation of signals of light indicators of an onboard communicator of Infiniti


All indicators are switched on

  • Short-term (30-second) activation of all indicators is made each time at ignition inclusion. Except for a situation of repeated inclusion within the 3-minute cycle ON-OFF-ON.
  • At identification by system of self-diagnostics of any deviations, shutdowns of indicators and at the included ignition do not occur. Serviceability of functioning of a communicator in this situation can appear broken.
  • If at inclusion of ignition the indicator is activated only, and the button of giving of a distress signal was not pressed, it can be regarded as a sign of violation of serviceability of functioning of system.


The indicator of the button of giving of a distress signal of "Mayday" works in a flashing mode

The blinking of the Mayday indicator is a sign of that the button of a signal transmission of disaster was pressed, and the onboard communicator undertakes attempts of installation of communication with the Center of Fast Reaction of Infiniti.


The indicator of the button of giving of a distress signal of "Mayday" works in a continuous mode

The continuous luminescence of the Mayday indicator is a sign of that the button of a signal transmission of disaster was pressed, and the onboard communicator made connection with the Center of Fast Reaction of Infiniti and carries out transfer of a standard information package.


The indicator of the button of inclusion of information mode works in a flashing mode

The blinking of the Information indicator is a sign of that the button of inclusion of a mode of an exchange was pressed by details, and the onboard communicator undertakes attempts of installation of communication with the Center of Fast Reaction of Infiniti.


The indicator of the button of inclusion of information mode works in a continuous mode

The blinking of the Information indicator is a sign of that the button of inclusion of a mode of an exchange was pressed by details, and the onboard communicator made connection with the Center of Fast Reaction of Infiniti and carries out transfer of a standard information package.


The indicator of a repeated call works in a flashing or continuous mode

Activation of this indicator is a sign of that the last attempt of installation of communication with the Communication Center Infiniti did not crown success and the communicator is in a mode of a repeated call (see above).


The stay indicator out of an area of coverage of a telecommunication network works in a continuous mode

Activation of this indicator testifies that the device of the cell phone is out of an area of coverage of a network and the onboard communicator is not capable to provide a communication channel with the Center of Fast Reaction. When using the optional telephone set the indicator will work with it in an asynchronous mode.


Indicators of a repeated call and stay out of an area of coverage of a telecommunication network work in a continuous mode

Simultaneous activation of two data of indicators testifies that at the moment of communication session installation the car was in an area of coverage of a telecommunication network, however then left it. The signal was lost and the communicator makes attempts of a repeated call.

In a similar situation of attempt of a repeated call will be made within the next 30 minutes.


Indicators of a repeated call and stay out of an area of coverage of a telecommunication network join periodically and switched off

The similar picture takes place, when the data exchange session between a communicator and the Center of Fast Reaction in a demonstration mode is established.


Requirements for fee of communication service Infiniti

For using services of communication service it is necessary to support in an active condition accounts of a telecommunication network (timely fee of provider of a network of mobile communication) and communication service Infiniti. Cancellation of any of two accounts will lead to impossibility of using the services provided by the Communication Center.


Operating restrictions

Data exchange with the Communication Center Infiniti is carried out on the communication channels provided by providers of mobile telephone systems in view of what on services of communication service all restrictions operating at using mobile communication extend.

A food of an onboard communicator is carried out from the storage battery established on the car which exit out of operation involves refusal of functioning of a communicator.


Distribution area

At the moment of drawing up of the real management the sphere of action of services of the communication Infiniti network extended on limits of 48 main continental states of the USA. On Alaska, Hawaii, in Canada and Mexico using services of a network it was not represented possible.


The restrictions connected with an overload of communication channels

The number of available channels of mobile telecommunication in various regions is unequal and at a full employment possibility of installation of the next session is blocked. In a similar situation the onboard communicator passes to a mode of a repeated call and will continue attempts of installation of communication during time till 2 o'clock (see above). Upon termination of attempts of a repeated call the system automatically comes back to a readiness mode.


Personal identification number (PIN) of a mobile telephone system

Some local providers of mobile telecommunication offer the users service at which each call from the cell phone is preceded by input of a special PIN code. The communication system Infiniti does not support this function and complete with such phone will not function.


Special functions of mobile telecommunication

Some providers of mobile telecommunication provide to the users a number of additional services, such as voice mail, call readdressing, a waiting mode and so forth — activation of similar functions can bring hindrances when using services of communication service Infiniti.


Being directed signals

During a communication session against a voice of the operator of the Communication Center there can sometimes be extraneous voices. Similar hindrances speak an interference at distribution of radio-waves and are not a sign of violation of serviceability of functioning of a communicator. If hindrances arise during transfer by a communicator of a standard information package, expulsion of the last repeats automatically.


Confidentiality

Data exchange with the Communication Center Infiniti is carried out on the communication channels provided by providers of mobile telephone systems, not rendering confidentiality services. Told extends and on information transferred from a communicator in the Center and back — the third party has possibility of listening of a communication channel.


False activation and parolirovaniye

At the conclusion of the contract with the Communication Center Infiniti to the user parolirovaniye service is applied. Application of the unique password will allow to identify the identity of the user in the following situations (for more details see above).

  • In need of penetration into the car without keys (keys are forgotten in salon).
  • At action under the threat of violence during data transmission on the channel of an emergency call of "Mayday".
  • By an automatic call of the Center during operation of the anticreeping alarm system.


The panel of switches of remote control established on a steering column functioning of the mobile phone

The panel of switches of remote control is fixed by functioning of the mobile phone a rim of a steering wheel (see an illustration the Scheme of an arrangement of governing bodies on the car dashboard).

By means of the switches located on the panel the driver can, without distracting from management of a vehicle to make answers to calls from the mobile phone, and also to regulate loudspeaker soundings.

For reception on a call of the mobile phone press the control panel button — the working audiosystem automatically will be disconnected (Auto mute mode) for the period of call reception. The repeated pressing the same button will transfer system to a mode of a voice communication. For completion of conversation it is enough to press the button once again.

By means of the top and bottom buttons of the control panel it is possible to regulate loudness of sounding of loudspeaker, - reception is conducted through a loudspeaker of the right forward door.


«on page back
2.3.3. Display of a conclusion of compass readings and sensor of temperature of external air
on the following page»
2.4. Comfort