Infiniti QX4 service since 1996 of release
1. Introduction
2. Maintenance instruction
3. Routine maintenance
4. Engine
5. Cooling and heating systems
6. Power supply systems and managements
7. Start and charge systems
8. Transmission line
9. Brake system
10. Suspension bracket and steering
10.1. Specifications
10.2. Assessment of the general condition of components of a suspension bracket and car steering
10.3. Check of a condition and replacement of spherical support of a forward suspension bracket
10.4. Check of a condition of steering drafts
10.5. Removal and installation of the cross-section lever of a forward suspension bracket
10.6. Adjustment of a pretightness of stupichny bearings of forward wheels
10.7. Removal, check of a condition and installation of screw springs and rack-mount assemblies of a forward suspension bracket
10.8. Removal and installation of stupichny assembly and rotary fist
10.9. Removal, check of a condition and installation of the forward stabilizer of cross-section stability
10.10. Replacement of stupichny bearings
10.11. Check of a condition of shock-absorbers and springs of a back suspension bracket
10.12. Removal and installation of components and assembly of a back suspension bracket
10.13. Removal, check of a condition and installation of levers of a back suspension bracket
10.14. Removal, check of a condition and installation of screw springs of a back suspension bracket
10.15. Removal and installation of shock-absorbers of a back suspension bracket
10.16. Removal and installation of the back stabilizer of cross-section stability
10.17. Removal, check of a condition and installation of a cross-section jet bar of a back suspension bracket
10.18. Pumping of a hydraulic path of a steering drive
10.19. Checks and adjustments of a steering wheel
10.20. Check of effort of resistance to sliding of a lath of the steering mechanism
10.21. Adjustment of a torque of a provorachivaniye of a leading gear wheel of the steering mechanism
10.22. Check of hydraulic pressure of GUR
10.23. Adjustment of effort of a tension of a belt of a drive of the steering pump
10.24. Removal and installation of reduktorny assembly
10.25. Removal and installation of assembly of the steering mechanism
10.26. Removal and installation of the steering pump
10.27. Removal and installation of a steering wheel
10.28. Removal and installation of assembly of the combined podrulevy switches
10.29. Removal and installation of the lock of ignition / blocking of a steering column
10.30. Removal, check of a condition and installation of a steering column
10.31. Corners of installation of forward wheels
11. Body
12. Electric equipment
 












10-27-snyatie-i-ustanovka-rulevogo-kolesa.html

10.27. Removal and installation of a steering wheel

Cars considered in the real Management are equipped with system of additional safety of SRS which is better known as a safety cushion. Before performing any works near assembly of a pillow or a steering column, without fail disconnect system in order to avoid receiving traumas as a result of its casual operation (see. Head Electric equipment). Isolation and contact sockets of electroconducting of a chain of SRS are painted in bright yellow color. It is not necessary to connect any diagnostic devices to this chain!


Removal

Bolts of fastening of the module of a safety cushion are planted on special hermetic and to a reuse are not subject.


 PERFORMANCE ORDER

  1. Before starting removal of a steering wheel, деактивируйте SRS (see. Head Electric equipment).
  2. Remove the bottom cover of a casing of a steering column.
  3. Disconnect electroconducting from the module of a driver's face-to-face safety cushion, then remove the left and right sections of a casing.
  1. By means of a key of the TORX type turn out bolts of fastening of the module (see the prevention).
  1. Remove a safety cushion and a spiral cable drum. Transfer assembly on a workbench and lay it a slip up.
  2. Bring forward wheels of the car into rectilinear situation.
  3. Disconnect horn electroconducting, and also all other electroconducting disturbing to removal of a steering wheel.
  4. Give a nut of fastening of a steering wheel, remove a washer and mark the provision of a wheel concerning a shaft of a steering column.
  1. By means of a special stripper remove a steering wheel and disconnect a cable of a drive of blocking of switching of AT.

Do not draw a stripper bolt! Do not make attempts of knocking down of a steering wheel by means of a hammer!


Installation

 PERFORMANCE ORDER

  1. Make sure that forward wheels still are in rectilinear situation.
  2. Check correctness of combination of a uvula of the sensor switch of the returnable device of the switch of indexes of turn with reciprocal risky the podrulevy switch.
  1. Make sure that the spiral cable SRS reel is in neutral (central) situation, and adjusting labels correctly are combined.

At the wrong installation the cable drum can appear jammed at strong deployment of a steering wheel!

  1. Establish a drum on a steering column. In case of need make drum centering for what turn it on 2.5 turns from extreme situation and achieve combination of adjusting labels. For reliability temporarily fix a drum in neutral situation by means of an adhesive tape.
  1. Connect to a cable drum electroconducting.
  2. Connect a cable of blocking of switching of AT.
  3. Establish a casing of a steering column and remove fixing cable drum an adhesive tape.
  4. Establish a steering wheel — track correctness of hit of a directing pin of a cable drum in reciprocal nests.
  5. Pass a cable drum in a wheel nave.
  6. Connect horn electroconducting, then enter a cable drum into gearing with ratchet doggies of a steering wheel.
  7. Tighten with demanded effort a nut of fastening of a steering wheel.
  8. Establish into place the safety cushion module, screw NEW fixing bolts and tighten them with demanded effort.
  9. Establish into place remained elements of a casing of a steering column.
  10. In summary make SRS activation (see. Head Electric equipment).


«on page back
10.26. Removal and installation of the steering pump
on the following page»
10.28. Removal and installation of assembly of the combined podrulevy switches