Infiniti QX4 service since 1996 of release
1. Introduction
2. Maintenance instruction
3. Routine maintenance
4. Engine
5. Cooling and heating systems
6. Power supply systems and managements
7. Start and charge systems
8. Transmission line
9. Brake system
10. Suspension bracket and steering
10.1. Specifications
10.2. Assessment of the general condition of components of a suspension bracket and car steering
10.3. Check of a condition and replacement of spherical support of a forward suspension bracket
10.4. Check of a condition of steering drafts
10.5. Removal and installation of the cross-section lever of a forward suspension bracket
10.6. Adjustment of a pretightness of stupichny bearings of forward wheels
10.7. Removal, check of a condition and installation of screw springs and rack-mount assemblies of a forward suspension bracket
10.8. Removal and installation of stupichny assembly and rotary fist
10.9. Removal, check of a condition and installation of the forward stabilizer of cross-section stability
10.10. Replacement of stupichny bearings
10.11. Check of a condition of shock-absorbers and springs of a back suspension bracket
10.12. Removal and installation of components and assembly of a back suspension bracket
10.13. Removal, check of a condition and installation of levers of a back suspension bracket
10.14. Removal, check of a condition and installation of screw springs of a back suspension bracket
10.15. Removal and installation of shock-absorbers of a back suspension bracket
10.16. Removal and installation of the back stabilizer of cross-section stability
10.17. Removal, check of a condition and installation of a cross-section jet bar of a back suspension bracket
10.18. Pumping of a hydraulic path of a steering drive
10.19. Checks and adjustments of a steering wheel
10.20. Check of effort of resistance to sliding of a lath of the steering mechanism
10.21. Adjustment of a torque of a provorachivaniye of a leading gear wheel of the steering mechanism
10.22. Check of hydraulic pressure of GUR
10.23. Adjustment of effort of a tension of a belt of a drive of the steering pump
10.24. Removal and installation of reduktorny assembly
10.25. Removal and installation of assembly of the steering mechanism
10.26. Removal and installation of the steering pump
10.27. Removal and installation of a steering wheel
10.28. Removal and installation of assembly of the combined podrulevy switches
10.29. Removal and installation of the lock of ignition / blocking of a steering column
10.30. Removal, check of a condition and installation of a steering column
10.31. Corners of installation of forward wheels
11. Body
12. Electric equipment
 








Когда закончится война астрологи | авто шумоизоляция цена в воронеже
8099f600






10-10-zamena-stupichnykh-podshipnikov.html

10.10. Replacement of stupichny bearings

Cм. illustration Design of stupichny assembly of a forward wheel.

 PERFORMANCE ORDER

  1. To Poddomkratta the car also establish it on props (see an illustration the Scheme of an institution of props for car fixing in the lifted situation). Remove the corresponding forward wheel.
  2. Disconnect electroconducting from the wheel ABS sensor.
  3. Turn out fixing bolts, remove a support and tie up it a wire to suspension bracket elements (see. Head Brake system).
  4. Turn out fixing bolts and remove a driving flange.
  5. Easy postukivaniye a hammer with brass brisk liberate from a nave a pin of the external CV JOINT of a power shaft.
  6. Remove a lock washer.
  7. Having used a special stripper of KV40105400, unscrew a nut of the stupichny bearing.
  8. Remove the external bearing and stupichny assembly.
  9. Remove an epiploon and the internal bearing.
  10. In case of need by means of a brass drift remove external and internal holders.
  11. Wash out components of bearings in solvent and dry them the compressed air.

Do not rotate bearings on air.

  1. Attentively examine bearings on existence of signs of wear and mechanical damages. Replace defective components.
  2. Installation is made as it should be, the return to an order of dismantle of components. Track, that all sealing elements and lock washers were replaced, and fixture will tighten with demanded effort.
  3. In summary do not forget to adjust a pretightness of bearings (see. Adjustment of a pretightness of stupichny bearings of forward wheels).


«on page back
10.9. Removal, check of a condition and installation of the forward stabilizer of cross-section stability
on the following page»
10.11. Check of a condition of shock-absorbers and springs of a back suspension bracket