Infiniti QX4 service since 1996 of release
1. Introduction
2. Maintenance instruction
3. Routine maintenance
4. Engine
5. Cooling and heating systems
6. Power supply systems and managements
7. Start and charge systems
8. Transmission line
9. Brake system
10. Suspension bracket and steering
10.1. Specifications
10.2. Assessment of the general condition of components of a suspension bracket and car steering
10.3. Check of a condition and replacement of spherical support of a forward suspension bracket
10.4. Check of a condition of steering drafts
10.5. Removal and installation of the cross-section lever of a forward suspension bracket
10.6. Adjustment of a pretightness of stupichny bearings of forward wheels
10.7. Removal, check of a condition and installation of screw springs and rack-mount assemblies of a forward suspension bracket
10.8. Removal and installation of stupichny assembly and rotary fist
10.9. Removal, check of a condition and installation of the forward stabilizer of cross-section stability
10.10. Replacement of stupichny bearings
10.11. Check of a condition of shock-absorbers and springs of a back suspension bracket
10.12. Removal and installation of components and assembly of a back suspension bracket
10.13. Removal, check of a condition and installation of levers of a back suspension bracket
10.14. Removal, check of a condition and installation of screw springs of a back suspension bracket
10.15. Removal and installation of shock-absorbers of a back suspension bracket
10.16. Removal and installation of the back stabilizer of cross-section stability
10.17. Removal, check of a condition and installation of a cross-section jet bar of a back suspension bracket
10.18. Pumping of a hydraulic path of a steering drive
10.19. Checks and adjustments of a steering wheel
10.20. Check of effort of resistance to sliding of a lath of the steering mechanism
10.21. Adjustment of a torque of a provorachivaniye of a leading gear wheel of the steering mechanism
10.22. Check of hydraulic pressure of GUR
10.23. Adjustment of effort of a tension of a belt of a drive of the steering pump
10.24. Removal and installation of reduktorny assembly
10.25. Removal and installation of assembly of the steering mechanism
10.26. Removal and installation of the steering pump
10.27. Removal and installation of a steering wheel
10.28. Removal and installation of assembly of the combined podrulevy switches
10.29. Removal and installation of the lock of ignition / blocking of a steering column
10.30. Removal, check of a condition and installation of a steering column
10.31. Corners of installation of forward wheels
11. Body
12. Electric equipment
 








8099f600 soap today






10-6-regulirovka-prednatyaga-stupichnykh-podshipnikov-perednikh-koles.html

10.6. Adjustment of a pretightness of stupichny bearings of forward wheels

 PERFORMANCE ORDER

  1. Remove a support of the brake mechanism with blocks (see. Head Brake system).
  2. Check purity of the bearing and availability of greasing in it. By means of a special stripper (KV40105400) tighten a stupichny nut with effort of 79 — 98 Nanometers. For a bearing usadka повращайте a nave in both directions.
  3. Release a nut so that there was a possibility of its rotation manually. Povrashchayte a nave in both directions, then again tighten a nut with effort 0.5 — 1.5 Nanometers.
  4. By means of a tsiferblatny measuring instrument of plunzherny type measure size axial люфта the bearing — the nominal rate makes 0.0 mm.
  5. By means of a dynamometer of the bezmenny type connected to one of wheel hairpins, check effort of a pretightness of the bearing.
  6. Hold on a stupichny nut in a range of 15 — 30 degrees, having provided possibility of adequate installation of a lock washer. Povrashchayte a nave in both directions, then once again measure size of a pretightness of the bearing. The nominal rate makes a difference between results of the second and first measurements and should not fall outside the limits a range 0.7 — 2.1 kgfs.


«on page back
10.5. Removal and installation of the cross-section lever of a forward suspension bracket
on the following page»
10.7. Removal, check of a condition and installation of screw springs and rack-mount assemblies of a forward suspension bracket