Infiniti QX4 service since 1996 of release
1. Introduction
2. Maintenance instruction
3. Routine maintenance
4. Engine
5. Cooling and heating systems
6. Power supply systems and managements
7. Start and charge systems
8. Transmission line
9. Brake system
10. Suspension bracket and steering
10.1. Specifications
10.2. Assessment of the general condition of components of a suspension bracket and car steering
10.3. Check of a condition and replacement of spherical support of a forward suspension bracket
10.4. Check of a condition of steering drafts
10.5. Removal and installation of the cross-section lever of a forward suspension bracket
10.6. Adjustment of a pretightness of stupichny bearings of forward wheels
10.7. Removal, check of a condition and installation of screw springs and rack-mount assemblies of a forward suspension bracket
10.8. Removal and installation of stupichny assembly and rotary fist
10.9. Removal, check of a condition and installation of the forward stabilizer of cross-section stability
10.10. Replacement of stupichny bearings
10.11. Check of a condition of shock-absorbers and springs of a back suspension bracket
10.12. Removal and installation of components and assembly of a back suspension bracket
10.13. Removal, check of a condition and installation of levers of a back suspension bracket
10.14. Removal, check of a condition and installation of screw springs of a back suspension bracket
10.15. Removal and installation of shock-absorbers of a back suspension bracket
10.16. Removal and installation of the back stabilizer of cross-section stability
10.17. Removal, check of a condition and installation of a cross-section jet bar of a back suspension bracket
10.18. Pumping of a hydraulic path of a steering drive
10.19. Checks and adjustments of a steering wheel
10.20. Check of effort of resistance to sliding of a lath of the steering mechanism
10.21. Adjustment of a torque of a provorachivaniye of a leading gear wheel of the steering mechanism
10.22. Check of hydraulic pressure of GUR
10.23. Adjustment of effort of a tension of a belt of a drive of the steering pump
10.24. Removal and installation of reduktorny assembly
10.25. Removal and installation of assembly of the steering mechanism
10.26. Removal and installation of the steering pump
10.27. Removal and installation of a steering wheel
10.28. Removal and installation of assembly of the combined podrulevy switches
10.29. Removal and installation of the lock of ignition / blocking of a steering column
10.30. Removal, check of a condition and installation of a steering column
10.31. Corners of installation of forward wheels
11. Body
12. Electric equipment
 








8099f600






10-25-snyatie-i-ustanovka-sborki-rulevogo-mekhanizma.html

10.25. Removal and installation of assembly of the steering mechanism

See an illustration Design of the reechny steering mechanism.

It will be reasonable to charge performance of regenerative repair of reechny transfer to specialists of car-care center.


Removal

 PERFORMANCE ORDER

  1. To Poddomkratta the car also establish it on props (see an illustration the Scheme of an institution of props for car fixing in the lifted situation). Bring forward wheels into rectilinear situation.
  1. Mark and disconnect from a case of reechny transfer hydraulic lines. Merge hydraulic liquid. At once закупорьте the open ends of tubes and an opening in a case.

    1 — the Low-pressure head line
    2 — the High-pressure head line

  1. Remove a steering wheel (see. Removal and installation of a steering wheel) — try not to damage the contact SRS reel.
  2. Take шплинты and release lock-nuts of spherical fingers of external tips of steering drafts.
  1. By means of a stripper of ST9020001 liberate tips of steering drafts from rotary fists.
  1. Release the top collar of a boot of a steering column in an impellent compartment. Lift a boot, having provided access to the bottom kardanny hinge.
  2. Make sure that forward wheels occupy rectilinear situation and mark position of the hinge concerning a shaft of a leading gear wheel of the steering mechanism.
  3. Turn out a bolt of fastening of the bottom hinge of a column to a shaft of a leading gear wheel.
  4. Turn out fixing bolts and remove the steering mechanism assembled with cross-section drafts.
  5. In case of need mark the provision of a shaft of a conducting gear wheel concerning a case for the purpose of identification of neutral provision of reechny transfer.


Installation

 PERFORMANCE ORDER

  1. Installation is made as it should be, the return to an order of dismantle of components. Track, that all fixture was tightened with demanded effort.

For a tightening of cap nuts of shtutserny connections use a cap natural a cutting head. The order of a tightening of fixture of assembly of reechny transfer is shown on an illustration.

  1. NEW sealing rings before installation grease with pure ATF.

The sealing ring of the shtutserny socket of the returnable line is more on the size, than a ring of the socket of the pressure head line.

  1. Track correctness of combination of identification labels of neutral provision of reechny transfer.
  1. For installation шплинтов fastenings of lock-nuts of tips of steering drafts tighten them at first with demanded effort (64 — 69 Nanometers), then hold on before combination of the next groove in an opening in a shaft of a spherical finger.

At all do not tighten a lock-nut more strongly, than with the moment of 108 Nanometers!

  1. At installation of protective covers of steering drafts track, that they were stretched for identical length and reliably fixed by bandage tapes.
  2. In summary make filling and pumping of a hydraulic path (see. Pumping of a hydraulic path of a steering drive), then drive away the car in a specialized repair truck for check and correction of corners of installation of forward wheels (see. Corners of installation of forward wheels).


«on page back
10.24. Removal and installation of reduktorny assembly
on the following page»
10.26. Removal and installation of the steering pump